Honda Accord 77960 TL0 E920 M1 - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: AIRBAG (https://cartechnology.co.uk/forumdisplay.php?fid=13) +--- Thread: Honda Accord 77960 TL0 E920 M1 (/showthread.php?tid=702) |
Honda Accord 77960 TL0 E920 M1 - junitechnic - 17-11-2013 Hi, I have Airbag 77960 TL0 E920 M1 TRW and I'm looking for bin from 95640, I can't read eeprom because somebody before Me destroy 2 pin in eeprom. I just have bin from 77960 TL0 G920 M1 but is still fault from driver tensioner and I,m not sure about difference between this modules. Please help Best Regards RE: Honda Accord 77960 TL0 E920 M1 - drewdoom - 17-11-2013 (17-11-2013, 00:05 AM)junitechnic Wrote: Hi, Hi.I heave dump from my friend but only with crash.We both dont heave tool to clear it. RE: Honda Accord 77960 TL0 E920 M1 - junitechnic - 17-11-2013 (17-11-2013, 21:32 PM)drewdoom Wrote: Hi.I heave dump from my friend but only with crash.We both dont heave tool to clear it. Hi, Thank You, I try compare with 77960 TL0 G920 M1 maybe will be fine, I put this G920 bin file but is still fault from driver tensioner and when I plug out this tensionsioner then is comes this same fault. When I fix this then I upload this bin. Best Regards RE: Honda Accord 77960 TL0 E920 M1 - drewdoom - 17-11-2013 (17-11-2013, 21:57 PM)junitechnic Wrote: Hi, Thank You, I try compare with 77960 TL0 G920 M1 maybe will be fine, I put this G920 bin file but is still fault from driver tensioner and when I plug out this tensionsioner then is comes this same fault. Maybe You heave to insert a rezistor 3ohm in circuit of tensioner and then check fault codes.I always do that.Regards RE: Honda Accord 77960 TL0 E920 M1 - junitechnic - 17-11-2013 Hi, Yes but in this output I have good tensioner I check with rezistor and I check tensioner, before I meet few situation when in fault codes not show crash just some component fault and after when I write clean file then problem/fault is gone, last time I have two ecu from Yaris no crash data stored but light is on, mostly I use KTS and Launch but sometimes descriptions fault is wrong I write clean file in Yaris airbag and work nice, and in read file I found crash Best Regards RE: Honda Accord 77960 TL0 E920 M1 - drewdoom - 17-11-2013 When is it about Yaris I mean old one,I never done crash I think this module just dont stored the crash.I was working with view toyotas and i just put new componets airbag and etc. after that light just turn off.But your case with honda just remind me something.I use to work with fiesta and there was igniter passenger airbag fault.I flashed many difrent dumps no succes.Solution was very easy My autocom heave some buggs with translation,changing sides of airbag. Good luck with honda.Cheers! RE: Honda Accord 77960 TL0 E920 M1 - junitechnic - 13-01-2014 Problem Solved I clean this crash file and work Thanks Drewdoom |