[brzndan]

Hello, sorry if the questions seems stupid, but I´ve looked everywhere and can´t find an answer: I installed ISTA 4.10.15, it's working perfectly, I'm trying to clear some error codes and get the message about tuning off the ignition and nothing happens. So I found out about the voltage thing, dowloaded the voltage control v3, did everything needed and ista opens fine as the vcontrol, it shows power 13.7 ignition 13.5

Now the question: how do I use it? I open the vcontrol then open Istagui? leave it at these numbers and perform the error code clearing and when it shows the message to turn off the igntion I do what? unclick the checkbox in the vcontrol?

[Node]

You can open and close control app at any time. Last settings are kept while ISTA is running. For clearing yes, you uncheck ignition checkbox. Then after ISTA tells you check it back. But for good results you need to switch ignition off and on manually too.

[brzndan]

You can open and close control app at any time. Last settings are kept while ISTA is running. For clearing yes, you uncheck ignition checkbox. Then after ISTA tells you check it back. But for good results you need to switch ignition off and on manually too.

Thank you very much, I'll try right now.

EDIT: It works perfectly, thank you. Although I couldn't clear my error with ISTA+, only with INPA, idk why.. But ow well, now I'm gonna start studying to see what else can I do in my BMW 330 2006. I downloaded the app Carly, but it only let you do stuff if you pay anualy. As I don't intend doing, I'm try to figure out how to do the same stuff with the programs I have installed in my PC (I'm trying to get the car to beep the horn when I lock or unlock).

[Node]

Support for v4.10.30 added.

[Harrycz44]

Hi
How setup ENET cable pleas?

I rename only in Ista+ folder Xenet32.dll to Xenet32.ebas.dll and downloaded files obd32.dll rename to Xenet32.dll and copy to BIN in Ista+ , after copy file NodeIstaVoltagecontroll.dll to BIN in ISTA+

After start ISTA+ got error IFH0027
thank you

[Node]

This solution is not designed to replace dlls starting with X in ediabas.

[motorberserker]

This solution is not designed to replace dlls starting with X in ediabas.

I got the same problem as Harrycz44.
It there any way to get the simulated voltage in ISTA+ with ENET cable?

[bimmer71]

got installed this evening will test in am on car all seems ok , inpa unsure of but ista+ is main concern here

once working think I write a batch file to backup oem file and do all the replacing needed then post here in text could take a week or to busy 50plus work week much thanks NODE

fyi I install inpa in a getto way seems to work for ediabas connection for ista+ all I worry about right now, if any one has a dummy proof way to install inpa would be nice !

[Node]

This solution is not designed to replace dlls starting with X in ediabas.

I got the same problem as Harrycz44.
It there any way to get the simulated voltage in ISTA+ with ENET cable?

Do you have any good reason for that? It would take time to develop such solution and up till now I don't know of any reason to do that.

[motorberserker]

This solution is not designed to replace dlls starting with X in ediabas.

I got the same problem as Harrycz44.
It there any way to get the simulated voltage in ISTA+ with ENET cable?

Do you have any good reason for that? It would take time to develop such solution and up till now I don't know of any reason to do that.

I thought for F-series, the ECU upgrade plan generation is allowed only when the voltage is detected in ISTA+. This is not a problem when using ICOM. However, for ENET cable the voltage is unknown without simulation tool.