Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Read 29F400
30-10-2015, 02:52 AM,
Post: #11
|
|||
|
|||
RE: Read 29F400
Friend, whenever you must work on the bench and you see 29f400, desolder it handly and read/write by programmer (BeeProg..for example) and correspond socket. It will take a short time, also, it is most safelly way. That's my friendly recommendation.
rgds, cuby |
|||
30-10-2015, 05:43 AM,
Post: #12
|
|||
|
|||
RE: Read 29F400
(30-10-2015, 02:52 AM)cubica Wrote: Friend, whenever you must work on the bench and you see 29f400, desolder it handly and read/write by programmer (BeeProg..for example) and correspond socket. It will take a short time, also, it is most safelly way. That's my friendly recommendation. i know but i need way to read without desolder |
|||
30-10-2015, 14:16 PM,
Post: #13
|
|||
|
|||
RE: Read 29F400
(30-10-2015, 05:43 AM)sayf Wrote:(30-10-2015, 02:52 AM)cubica Wrote: Friend, whenever you must work on the bench and you see 29f400, desolder it handly and read/write by programmer (BeeProg..for example) and correspond socket. It will take a short time, also, it is most safelly way. That's my friendly recommendation. Maybe FGTech Galletto v53/54 can do that? OR Kess? Was I helpful? Please support my time and Hit And -button's. NEW Trasdata 9 Master support Bosch SM(service mode) etc |
|||
30-10-2015, 23:25 PM,
Post: #14
|
|||
|
|||
RE: Read 29F400
(30-10-2015, 14:16 PM)Bimmeristi Wrote:(30-10-2015, 05:43 AM)sayf Wrote:(30-10-2015, 02:52 AM)cubica Wrote: Friend, whenever you must work on the bench and you see 29f400, desolder it handly and read/write by programmer (BeeProg..for example) and correspond socket. It will take a short time, also, it is most safelly way. That's my friendly recommendation. yes, but not always for sure. rgds, cuby |
|||
31-10-2015, 11:16 AM,
Post: #15
|
|||
|
|||
RE: Read 29F400
That's why it's safer to remove and read/write in a programmer
Ie labtool 48xp, beeprog, up48a etc The up48a reads and writes this ic in 17 seconds if my post helps please give Reputation and Thanks
|
|||
06-11-2015, 12:52 PM,
Post: #16
|
|||
|
|||
RE: Read 29F400
|
|||
08-11-2015, 11:19 AM,
Post: #17
|
|||
|
|||
RE: Read 29F400
What image?
I didn't post one if my post helps please give Reputation and Thanks
|
|||
09-11-2015, 23:36 PM,
Post: #18
|
|||
|
|||
RE: Read 29F400
BEST solution & safe mode (desolder) , boot mode sometimes read bad & u ll lost ori data,use labtool beeprog best tool
|
|||
18-05-2019, 09:33 AM,
Post: #19
|
|||
|
|||
RE: Read 29F400
Hi,
I need to read/write 29F400BC for BMW CCC NAVI.Any Ideea wich programmer do the job?For resonable price. Thank you! |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content