[Node]

With D-Cable it runs fine. I was able to delete adaptions finally Great Work.

Is it possible to use it with a passthru device like openport? It runs almost fine, but ignition is not is not recognized.

Another question: Why there are two ediabas folders? One und c:/ediabas and another inside Ista Folder? I only use Ista, so could i just delete that c:/ediabas one?

You get C:\ediabas when you install standard tools. Uninstall them and it will be removed (at least most of it , but you can delete it afterwards.

I am not familiar with openport. HOW do you use it in ediabas???

[b3dn]

You get C:\ediabas when you install standard tools. Uninstall them and it will be removed (at least most of it , but you can delete it afterwards.

I am not familiar with openport. HOW do you use it in ediabas???

Thx for the Info. First i´ve set up an ordinary Dcan Cable in ediabas with your voltage control. Everything is fine.
Now, i´ve set up openport as passthru in ISTA+ settings. It reads voltage but no ignition. Setting up that device in ediabas as interface=passthrud but i´ve no luck. Will investigate it, maybe wrong settings.... If i got it running via ediabas is it possible to set up the voltage control on passthru devices (passthrud.dll renamed to passthrud.ebas.dll)?

[Node]

You get C:\ediabas when you install standard tools. Uninstall them and it will be removed (at least most of it , but you can delete it afterwards.

I am not familiar with openport. HOW do you use it in ediabas???

Thx for the Info. First i´ve set up an ordinary Dcan Cable in ediabas with your voltage control. Everything is fine.
Now, i´ve set up openport as passthru in ISTA+ settings. It reads voltage but no ignition. Setting up that device in ediabas as interface=passthrud but i´ve no luck. Will investigate it, maybe wrong settings.... If i got it running via ediabas is it possible to set up the voltage control on passthru devices (passthrud.dll renamed to passthrud.ebas.dll)?

It could be.

[7eventy7even]

Any chance off support 4.41.41 ? Thanks

[Sedoy]

Any chance off support 4.41.41 ? Thanks

For what you need it? I succesfully tested newest ISTA with D-Can without VoltageControl. Maybe is depend on D-Can Adapter, i don't know.

Only for optical display fake Voltage?

[7eventy7even]

Any chance off support 4.41.41 ? Thanks

For what you need it? I succesfully tested newest ISTA with D-Can without VoltageControl. Maybe is depend on D-Can Adapter, i don't know.

Only for optical display fake Voltage?

I have problem with ignition,dont need optical display, its not working with my cable... maybe old one... and need new one ?!

[Sedoy]

Ok, if not working with your cable then need VoltageContol.

---

Here only IstaOperation.exe v4.41.41.25274, all other files use from old archive.

[Node]

I could make support for it, but not until mid-weekend as the earliest.

[7eventy7even]

Ok, if not working with your cable then need VoltageContol.

---

Here only IstaOperation.exe v4.41.41.25274, all other files use from old archive.

Everything is working now... Thanks

[iTudor]

I don't know if I'm doing it right, these are the steps I follow

In folder Ediabas/bin rename obd32.dll to obd32.ebas.dll, copy new obd32 on Ediabas/bin 
Remplace IstaOperation.exe with the same version folder included in rar.

open .exe and open ista, no voltage showed up.

try in 4.32.15 and 4.39.20