Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Changed ZGW lots of error in ISTA
25-09-2023, 15:45 PM,
Post: #1
|
|||
|
|||
Changed ZGW lots of error in ISTA
|
|||
25-09-2023, 20:53 PM,
Post: #2
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
Does the NBT Unit require K-Can2 High and Low to startup? right now it's connectetd to K-Can
|
|||
25-09-2023, 21:00 PM,
Post: #3
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
NBT HU need KCAN2 and right iDrive Controller.
If my post helped you hit the thanks and reputation button. Thank you.
|
|||
25-09-2023, 21:07 PM,
Post: #4
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
|
|||
25-09-2023, 21:24 PM,
Post: #5
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
You need KCAN2 from ZGW and you can’t use the old controller. You need also new controller connected to KCAN2.
If my post helped you hit the thanks and reputation button. Thank you.
|
|||
25-09-2023, 21:29 PM,
Post: #6
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
Might just literally need flexray initialization just like the fault. Be careful of this step though, you need to be confident that the Flexray CAN network is intact and everything is communicating. If there is a module that is not communicating, the initialization process will store it in the ZGW configuration, and I've been told you only have 1 shot to get it correct or you buy another ZGW.
Can you post a screenshot of the network tree? |
|||
25-09-2023, 21:30 PM,
Post: #7
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
(25-09-2023, 21:24 PM)user_530d Wrote: You need KCAN2 from ZGW and you can’t use the old controller. You need also new controller connected to KCAN2. Ok, guess i'll switch over the controller aswell then, to bad i didn't order 0.35mm2 Yellow/red and Yellow/brown cables for the K-Can2 High and K-Can2 Low (I recently ordered a lot of 0.35mm2 dual color cable from Germany) I like to do things properly |
|||
26-09-2023, 17:01 PM,
Post: #8
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
|
|||
26-09-2023, 17:59 PM,
Post: #9
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
Connect MOST from HU to KOMBI. Remove Combox. Write your actual SVT to VCM. Remove Combox components from VO.
If my post helped you hit the thanks and reputation button. Thank you.
|
|||
26-09-2023, 20:40 PM,
(This post was last modified: 26-09-2023, 21:15 PM by Haug530d.)
Post: #10
|
|||
|
|||
RE: Changed ZGW lots of error in ISTA
(26-09-2023, 17:59 PM)user_530d Wrote: Connect MOST from HU to KOMBI. Remove Combox. Write your actual SVT to VCM. Remove Combox components from VO. I took the Combox out of Most before i installed the NBT and i wrote TH VO to ZGW on bench before i installed the 8sk, NBT and Idrive wheel, so VO is correct. Everything seems to work, but nothing happens then i put the shifter in reverse, well that is nothing showing up on the screen i mean, as in no picture for the back up camera, what could be wrong? i have 3AG in the VO. |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content