Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
KT200 v2 full with offline dongle FEEDBACK
19-04-2024, 14:44 PM,
(This post was last modified: 19-04-2024, 14:45 PM by pinotec.)
Post: #81
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
(17-04-2024, 07:01 AM)sp852 Wrote: PSA Valeo V46.11 yesterday same ecu valeo v46.11 read..write ..read again... on bench ,all ok checksum calculate automatic, try on car.. all ok sure problem is kt200? used cable obd on bench or multicable ?because for bench need resistor 120 ohm between cable canbus ecu have this number: 98 00 91 30 80 98 00 91 30 80 |
|||
19-04-2024, 17:51 PM,
Post: #82
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
Edc16u34 read write chk obd ok
|
|||
20-04-2024, 08:17 AM,
(This post was last modified: 20-04-2024, 08:17 AM by xginx.)
Post: #83
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
continental GPEC4 sometime can read most of the time no
and at the end ecu cannot reconize in the car what is the resistor of the cnf1 pin when i messure it . it show 0 ohm... |
|||
20-04-2024, 14:14 PM,
(This post was last modified: 20-04-2024, 14:15 PM by tintoverano.)
Post: #84
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
EDC15VM+ bench read flash+eeprom OK
write not so much - reported to vendor |
|||
20-04-2024, 16:46 PM,
(This post was last modified: 20-04-2024, 16:49 PM by sp852.)
Post: #85
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
(19-04-2024, 14:44 PM)pinotec Wrote:(17-04-2024, 07:01 AM)sp852 Wrote: PSA Valeo V46.11 yes I did the reading and writing in banch, with this pinout can you give more on canbus with resistance 120 ohm |
|||
21-04-2024, 05:11 AM,
(This post was last modified: 21-04-2024, 05:15 AM by raffy haddad.)
Post: #86
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
120 ohm resistence must be conected on can lines one end to H and second end to L
Regards P.s.: isnt tool should be prepared for can 120ohm ? I don't have the tool but just a thought Personally i have made cable with switch to conect 120 ohm between can lines Always new stuff to learn
Skype: raffy.haddad File services : multi brand ecu immo off , VW solutions : immo transfer immo off , pcr 2.1 immo , BMW EDC16 IMMO OFF , .... Yamaha smart key supply pin code from dump ( TMAX , XMAX ) Chevrolet simens sirus D3x D4x D5x delphi MR 140 IMMOOFF I DO MY BEST HERE TO HELP YOU MAKE SOME $$$ BUT ON PRIVATE IS DIFFERENT Members who not report back they're name will be black listed on my list |
|||
Reputation: +4 - ROD-BENDERS [+1] , dabaca [+1] , Abou-raffik [+1] , loki954 [+1] | |||
21-04-2024, 10:54 AM,
Post: #87
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
toyota denso with 76f0085
read/write and chk by tool went OK No help for people not give a feedback
|
|||
Reputation: +4 - ROD-BENDERS [+1] , raffy haddad [+1] , dabaca [+1] , Abou-raffik [+1] | |||
21-04-2024, 23:09 PM,
Post: #88
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
(21-04-2024, 05:11 AM)raffy haddad Wrote: 120 ohm resistence must be conected on can lines one end to H and second end to L Bench cable on kt200 has already 120 ohms resistor installed in factory |
|||
Reputation: +1 - raffy haddad [+1] | |||
22-04-2024, 07:10 AM,
(This post was last modified: 22-04-2024, 07:17 AM by sp852.)
Post: #89
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
thank you for your answers friends,
it is not a problem of 120 ohm resistance, already the KT200II cable is equipped with a 120 ohm resistance, I checked it on my cable |
|||
Reputation: +1 - raffy haddad [+1] | |||
22-04-2024, 18:47 PM,
Post: #90
|
|||
|
|||
RE: KT200 v2 full with offline dongle FEEDBACK
mercedes sid310
read/write chk by tool ok No help for people not give a feedback
|
|||
Reputation: +4 - al70 [+1] , ROD-BENDERS [+1] , raffy haddad [+1] , ptalev [+1] | |||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content